AUDI VW INTAKE MANIFOLD ACTUATOR LINK ARM SHORT 1″ ( 077198327A Replacement)

AUDI VW INTAKE MANIFOLD ACTUATOR LINK ARM SHORT 1″ ( 077198327A Replacement)

Typically, the O.E.M. part is not sold alone – car dealers only sell it in a kit (P/N 077198327a) which costs around $400 per side (most cars require replacement on both sides, totaling in $800!!!)

The installation is fast and easy, simply remove the damaged part (you may need a screwdriver or pliers) and snap the end links of the new part onto the actuators. That is all!

Please Note: There are two available sizes of linkage arms [short (1″) or long (2″)]. Please choose the size appropriate for your car model, year, and/or assembly plant.

Why do you need two piece 2 pieces??
If you never changed the linkage arms and one of them is broken, probably in another it will break very quickly, because both have been subjected to the same conditions.
We recommend replacing both parts at the same time and avoid future problems.

If your vehicle has a broken link arm in the variable intake manifold system – a common problem due to the poor quality of the material used in the O.E.M. part – this listing offers you the most economical and reliable solution and is backed by a LIFETIME WARRANTY.

The Difference is in the Material Used:

These parts are made of DELRIN (an engineering polymer used in precision parts requiring high stiffness, low friction and excellent dimensional stability) used in industries for automobiles, planes, boats, aerospace, etc. It is a common replacement for metal in many applications such as gears, pulleys, impellers, etc.

Note about part compatibility:

Due in some cases the same model of Audi or VW could be use the link arm 1inch long or 2inch long depending of factors how assembly plant, you will be sure which size your car need. You must measure your OEM linkage arms and select the correct length for your car, or ask to you mechanics or car dealer.

The dimension is an estimate, from center of the ball to center of the ball on the arm.

Please determine if your car has the long (2”) or short (1”) manifold link arms before you buy.

Key Characteristics:
• High mechanical strength and rigidity
• Toughness and high resistance to repeated impacts
• Long-term fatigue endurance
• Excellent resistance to moisture, gasoline, solvents, and many other chemicals
• Good resilience and resistance to creep
• Natural lubricity
• Wide end-use temperature range (-100f to 300f)
• Good electrical insulating characteristics

***LIFETIME WARRANTY***

Fits the following vehicles and replaces linkage arms in P/N 077-198-327A, 077198327A :
2004-2007 VW Phaeton V8
2003+ VW Touareg V8
2002-2004 Audi A6/Avant V8
1998-2004 Audi A6/S6 Quattro V8
2000+ Audi A8/S8 Quattro V8

Pull the intake manifold 077198327A Audi VW – 1 inch
If you car is Audi or Volkswagen with an eight cylinder engine, with a volume of 3.7 or 4.2 liter, then you can face such a problem as breakage pull the intake manifold 077198327a.
If on your car there is the following:
Poor engine performance at low rpm;
Increased consumption of gasoline.

Probably caused by faulty rods, governing the geometrical parameters of the collector.

The vacuum regulator, using the plastic rod that actuates the intake manifold flaps. In use, the plastic wears down and becomes less strong and the lever is broken or breaks the attachment area. After that the craving begins to fly. The manufacturer does not implement this “little stuff” separately. In the store you can only buy vacuum regulator 077198327a entirely.
This item costs about $300, so buying parts can result in a lot of money.
Our designed and manufactured kit thrust manifold intake 077198327A.
You will be able to fix this problem.

The replacement procedure:
remove the old thrust dampers Audi or another car
install the new thrust manifold Audi.

You should know that there are two sizes of rods 1 and 2 inches, 2.5 and 5 cm to Know what craving intake manifold Audi you need is quite simple, you should only

to measure those that are installed on your car. Size we Have both.

We recommend you to change the kit. Most often, if one pull is out of order, the other will soon break.

In the manufacture of these items uses a special polymer Delrin. From this material produce parts that require high precision and stiffness.

This polymer is made of precision parts for aircraft, automobiles and other special equipment. This material successfully was able to replace

steel in the manufacture of gears, pulleys, impellers.

Suitable for the following vehicles and replaces the connecting lever in P / n 077-198-327A, 077198327A